View MT190AW01-V0_7747734.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

inno l u x display corporation m t190aw01 v.0 lcd module specification ( ) preliminary specification ( ) final specification customer checked & approved by ap proved by checked by prepared by pd qr a pd pdm i nnolux display corporation, no.160 kesyue rd., chu-nan site, hsinchu science par k, chu- nan 350 , miao-li count y, taiw an tel: 886-37-586000 fax: 886-37-586060 document number: mt190aw01 v.0-dr2-03 www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
innolux copyright a ll rights reserved, copying forbidden. record of revision version revise date p a g e content 01 2006-01-25 f i r s t e d it i o n t o a l l 02 2006-2-16 4 revise the definition of colour saturation and tco03 03 2006-2-24 14 change backlight connector www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 3/23 contents: a. general specification b. electrical specifications 1. pin assignment 2. absolute maximum ratings 3. electrical characteristics a. typical operating conditions b. display color vs. input data signals c. input signal timing d. display position e. backlight driving conditions c. optical specifications d. reliability test items e. safety f. display quality g. handling precaution h. label i. mechanical drawings appendix www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 4/23 a. general specification no. item specification remark 1 display resolution (pixel) 1 ,440(h) x 900(v), wxga + resolution 2 active area (mm) 4 10.4(h) x 256.5(v) 3 screen size (inch) 1 9 inches diagonal 4 pixel pitch (mm) 0 .285(h) x 0.285(v) 5 color configuration r , g, b vertical stripe 6 overall dimension (mm) 4 27.2(w) x 277.4(h) x 17(d) (typ.) 7 weight (g) 2 500 (max.) 8 surface treatment a nti-glare, haze = 25%, hard coating (3h) 9 input color signal 8 bit lvds 10 display colors 1 6.2m (6 bit with frc) 11 optimum viewing direction 6 oclock 12 backlight 4 ccfl 13 rohs r ohs compliance www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 5/23 b. electrical specifications 1 .pin assignment connector jae fi-xb30ssrl-hf16, foxconn gs23302-0311r-7f or mechanical interface equivalent connector. www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 6/23 #1 #30 #1 #30 #1 #30 rear view of lcm #1 #30 www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 7/23 2. absolute maximum ratings values parameter s ymbol min. max. unit remark power voltage v cc - 0.3 6 v at 25 c input signal voltage v lh - 0.3 4.3 v at 25 c operating temperature top 0 50 c note 1 storage temperature t st - 2 5 60 c note 2 ccfl current icfl - 7.5 [ma] n ote 1: the relative humidity must not exceed 90% non-condensing at temperatures of 40c or less. at temperatures greater than 40c, the wet bulb temperature must not exceed 39c. note 2: the unit should not be exposed to corrosive chemicals. 0 10 20 30 40 50 60 70 80 90 100 -40 -20 0 20 40 60 80 relative humidity(%rh) t emperature( c) operation range storage range www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 8/23 3. electrical characteristics a. typical operating conditions item symbol min. typ. max. unit remark input voltage v c c 4.5 5 5.5 v p ermissive power input ripple v rf - - 0.1 v black i c c - 700 1000 note 1 white i c c - 500 700 note 2 input current m osaic i cc - 700 1000 ma note 3 rush current i r ush - 1.6 3 a note 4 common mode voltage v cm - 1.2 - v differential input voltage vid 100 - 600 m v threshold voltage (high) vth - - 100 m v note 5 logic input voltage l vds: in+, in- threshold voltage (low) vtl -100 - - m v note 5 n ote 1 : the specified current is under the v cc =5v, 25 c, fv=60hz (frame frequency) condition whereas black pattern is displayed. note 2 : the specified current is under the vcc =5v, 25 c, fv=60hz (frame frequency) condition whereas white pattern is displayed. note 3 : the specified current is under the vcc =5v, 25 c, fv=60hz (frame frequency) condition whereas mosaic pattern(black & white [8*6] ) is displayed. white : 255 gray black : 0 gray www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 9/23 note 4 : test condition : (1) v dd = 5 v, v dd rising time = 470 s 10% (2) pattern: mosaic pattern (3) test circuit note 5 : lvds signal definition vid = vin + C vin- , vcm = vcm + Cvcm- , vid = vid + Cvid- , vid+ = vih + Cvih- , vid- = vil + Cvil- , vcm = (vin + +vin-)/2, vcm+ = (vih + +vih-)/2, vcm- = (vil + +vil-)/2, 90 % ton=470 s 10% v dd 5 v 12v v d d ( lcd input) control signal (high to low) m2 2sk1399 m1 2sk1059 r2 1k c2 10000pf c3 1uf r3 47k r1 47k fuse c1 1uf vin + = positive differential data & clk input vin- = negative differential data & clk input www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 10/23 note 6 : power on sequence for lcd v dd p arameter value u nit m in typ max ms t1 0.5 -- 10 ms t2 0 -- 50 ms t3 0 -- 50 ms t4 500 -- -- ms t5 450 -- -- ms t6 90 -- -- ms t7 -- -- tbd ms www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 11/23 b. display color vs. input data signals the brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color; the higher the binary input, the brighter the color. the table below provides a reference for color versus data input. color input color data red green blue msb lsb msb lsb msb lsb r7 r6 r5 r4 r3 r2 r1 r0 0 1 0 0 0 1 1 1 bl ack red(255) green(255) blue(255) cyan magenta yellow white 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 basic colors 0 0 0 : 1 1 1 red(000) dark red(001) red(002) : red(253) red(254) red(255) bright 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 red 0 0 0 : 0 0 0 green(000)dark green(001) green(002) : green(253) green(254) green(255) bright 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 green 0 0 0 : 0 0 0 blue(000) dark blue(001) blue(002) : blue(253) blue(254) blue(255) bright 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 blue 0 1 0 0 0 1 1 1 0 0 1 : 0 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 1 0 0 0 1 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 g7 g6 g5 g4 g3 g2 g1 g0 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 12/23 c. input signal timing support input timing table www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 13/23 d. display position d(1, 1) d(2, 1) d(720, 1) d(1439, 1) d(1440, 1) d(1, 2) d(2, 2) d(720, 2) d(1439, 2) d(1440, 2) . . . . . . . . . . . . d(1, 450) d(2, 450) d(720, 450) d(1439, 450) d(1440, 450) . . . . . . . . . . . . d(1, 899) d(2, 899) d(720, 899) d(1439, 899) d(1440, 899) d(1, 900) d(2, 900) d(720, 900) d(1439, 900) d(1440, 900) e . backlight driving conditions parameter symbol min. typ. max. unit remark remark lamp voltage v l (612) (680) (748) vrms lamp operation current il (2) (7) (7.5) marms note 1 (1200) t = 25 c note 2,3,4,5 lamp starting voltage vlstart (1700) vrms t = 0 c note 2,3,4,5 frequency f (40) - (80) khz note 5 lamp life time (40000) hr note 6 n ote: the waveform of the voltage output of inverter must be area-symmetric and the design of the inverter must have specifications for the modularized lamp. the performance of the backlight, such as lifetime or brightness, is greatly influenced by the characteristics of the dc-ac inverter for the lamp. all the parameters of an inverter should be carefully designed to avoid producing too much current leakage from high voltage output of the inverter. when designing or ordering the inverter please make sure that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. if the above situation is confirmed, the module should be operated in the same manners when it is installed in your instrument. note 1 : the degree of unbalance: less than 10% the ratio of wave height: less than 10%2 t he degree of unbalance = |ip-i-p| /irms*100(%) the ratio of wave height = ip(or i-p)/irms lamp should be completely turned on. ip i -p ip: high side peak i-p: low side p eak www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 14/23 note 2: test equipment: as-114b note 3: the voltage shown above should be applied to the lamp for more than 1 second after startup. otherwise, the lamp may not be turned on normally. note 4: inverter should provide more than min. value, and then lamp could be completely turned on note 5: lamp frequency may produce interference with horizontal synchronous frequency and this may cause line flow on the display. therefore lamp frequency shall be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. note 6: lamp life definition : the brightness of lamp becomes 50% of the initial brightness or not normal lighting. backlight connector : iwsa-02000-0241 pin no. symbol function remark 1 vih lamp high voltage input cable color: pink 2 v il lamp low voltage input cable color: white 3 vih lamp high voltage input cable color: blue 4 v il lamp low voltage input cable color: black www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 15/23 c. optical specifications specification item s ymbol condition m in. typ. max. unit remark tr (1.5) (6.5) tf (3.5) (8.5) response time t r+tf = 0 5 15 ms note 4 contrast ratio c r = 0 (500) (700) note 3,5 top c r R 10 cr R 5 (70) tbd (80) tbd bottom c r R 10 cr R 5 (70) tbd (80) tbd left c r R 10 cr R 5 (70) tbd (80) tbd viewing angle r ight cr R 10 cr R 5 (70) tbd (80) tbd deg. note 3,5,7 brightness ( center ) y l 250 300 n it note 3,6 wx 0.313 wy 0.329 rx (0.636) ry (0.349) gx (0.290) gy (0.589) bx (0.143) color chromaticity(cie) by = 0 -0.03 (0.080) +0.03 note 3 white uniformity (9 ) w 0.75 0.80 note 3,8 cross talk ct 2 % note 9 n ote 1: ambient temperature = 25c. note 2: to be measured in dark room after backlight warm up 30 minutes. note 3: to be measured with a viewing cone of 2by topcon luminance meter bm-5a. note 4: definition of response time: the output signals of bm-7 are measured when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the response time interval is between the 10% and 90% of amplitudes. refer to figure as below. www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 16/23 note 5. definition of contrast ratio: contrast ratio is calculated by the following formula. note 6: driving conditions for ccfl: i l = 7 ma, 50 khz frequency. note 7: definition of viewing angle note 8: definition white uniformity: luminance are measured at the following nine points (p1~p9). s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" " white" 0% 10% 90% 100% contrast ratio (cr)= brightness on the "white" state b rightness on the "black" state w = minimum brightness of nine points ( p 1~ p9 ). maximum brightness of nine points ( p 1~ p9 ). www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 17/23 n ote 9: l l a -l a l / l a x 100%= 2% max., l a and l a are brightness at location a and a l l b -l b l / l b x 100%= 2% max., l b and l b are brightness at location b and b note 10: optical characteristic measurement setup. 0 gray level 1/2 1/2 1/6 1/6 a b 1/2 1/2 1/6 1/6 2/3 1/3 1/3 2/3 a b 127 gray level 127 gray level www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 18/23 all rights strictly reserved. any portion of this prper shall not be reproduced, copied, or transformed to any other forms without permission from innolux display corporation. d. reliability test items test item test condition judgment remark high temperature storage 6 0c, 240hrs note 1 note 2 low temperature storage - 25c, 240hrs note 1 note 2 high temperature & high h umidity operation 40c, 90%rh, 240hrs (no condensation) note 1 note 2 high temperature operation 5 0c, 240hrs note 1 note 2 low temperature operation 0 c, 240hrs note 1 note 2 thermal shock ( non-operation) -20c~60c 1hr, 10mins, 1hr, 100cycles note 1 note 2 electrostatic discharge (esd) (non-operation) c ontact:+/-8kv, 150pf(330ohms), 25 times/1 point, 1 time/1 sec air discharge:+/-15kv, 150pf(330ohms ), 25 times/1 point, 1 time/1 sec n ote 1 note 2 vibration ( non-operation) vibration level : 1.5g bandwidth : 10-300hz waveform : sine wave, sweep rate : 10min 30 min for each direction x, y, z (1.5 hrs in total) note 1 note 2 mechanical shock ( non-operation) shock level : 50g, 11ms waveform : half sine wave direction : x, y, z one time each direction note 1 note 2 mtbf demonstration 40,000 hours with confidence level 90% note 1 note 3 n ote 1 : pass: normal display image with no obvious non-uniformity and no line defect. partial transformation of the module parts should be ignored. fail: no display image, obvious non-uniformity, or line defects. note 2 : evaluation should be tested after storage at room temperature for one hour. note 3 : the mtbf calculation is based on the assumption that the failure rate distribution meets the exponential model. www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 19/23 all rights strictly reserved. any portion of this prper shall not be reproduced, copied, or transformed to any other forms without permission from innolux display corporation. e. safety (1) sharp edge requirements there will be no sharp edges or corners on the display assembly that could cause injury. (2) materials a. toxicity there will be no carcinogenic materials used anywhere in the display module. if toxic materials are used, they will be reviewed and approved by the responsible innolux toxicologist. b. flammability all components including electrical components that do not meet the flammability grade ul94-v1 in the module will complete the flammability rating exception approval process. the printed circuit board will be made from material rated 94-v1 or better. the actual ul flammability rating will be printed on the printed circuit board. c. capacitors if any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards. f. display quality the display quality of the color tft-lcd module should be in compliance with the innoluxs incoming inspection standard. g. handling precaution the handling of the tft-lcd should be in compliance with the innoluxs handling principle standard. www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 20/23 all rights strictly reserved. any portion of this prper shall not be reproduced, copied, or transformed to any other forms without permission from innolux display corporation. h. label (1) module label (a) model number: mt190aw01 (b) version: v.0 (c) serial id i: z 1 z 2 z 3 z 4 z 5 z 6 z 7 z 8 z 9 z 10 z 11 z 12 serial id includes the information as below: 1. manufactured date: year: 0~9, for 2000~2009 2. month: 1~9 & a~c for jan.~dec. 3. date: 1~9 & a~z (exclude i, o, q, u) for 1th~31th 4. code of grade: 1, 3, 5, 7, e 5. serial no: module manufacture sequence no (d) serial id ii (inl internal use) mt190aw01 a m1900004 v.0 0 xx made in xxx z 1 z 2 z 3 z 4 z 5 z 6 --z 7 -- z 8 z 9 z 10 z 11 z 12 28 mm serial no code of grade year, month, date inl internal use innolux display inl internal use z 1 'z 2 '-z 3 ' z 4 'z 5 'z 6 'z 7 '-z 8 ' - z 9 '- z 10 '- z 11 ' z 12 '-z 13 '-z 14 ' z 15 ' -z 16 '-z 17 'z 18 ' z 19 ' -z 20 'z 21 'z 22 ' z 23 ' inl internal use 83 mm www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
s pec no. m t 1 9 0 aw 0 1 v. 0 p age 21/23 all rights strictly reserved. any portion of this prper shall not be reproduced, copied, or transformed to any other forms without permission from innolux display corporation. (2) carton label 120 mm (a) model number: mt190aw01 (b) version: v.0 (c) packing quantity: 5 pcs (d) serial id: z 1 z 2 z 3 z 4 z 5 z 6 z 7 z 8 z 9 serial id includes the information as below : (a) manufactured date: year: 0~9, for 2000~2009 month: 1~9 & a~c for jan.~dec. date: 1~9 & a~z (exclude i, o, q, u) for 1th~31th (b) code of grade: 1, 3, 5, 7, e (c) serial no: module packing sequence no innolux display bo x id : z 1 z 2 z 3 z 4 -- z 5 -- z 6 z 7 z 8 z 9 model no. mt190aw01 v.0 am1900004 0xx quantity : 5 pcs mfg date: 20xx/xx/xx made in xxx qc: 100 mm serial no code of grade year, month, date inl internal use www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
spec no. : mt 19 0 aw 01 v. 0 page : 22/23 all rights strictly reserved. any portion of this prper shall not be reproduced, copied, or transformed to any other forms without permission from innolux display corporation. i. me drawing (1) front view www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
spec no. : mt 19 0 aw 01 v. 0 page : 23/23 all rights strictly reserved. any portion of this prper shall not be reproduced, copied, or transformed to any other forms without permission from innolux display corporation. (2) back view www.bdtic.com/innolux/ free datasheet http://www.0pdf.com
http://www.bdtic.com/innolux www.bdtic.com/innolux/ free datasheet http://www.0pdf.com

▲Up To Search▲

Price & Availability of MT190AW01-V0

	To Download MT190AW01-V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .